Pool Dose Lab

Calcium Hardness Calculator

Enter your pool volume, hardness reading and target to see how much calcium chloride to add — or, if hardness is too high, how much water to drain and refill based on your tap water.

Last reviewed · How we calculate

Your pool

Not sure? Work it out from your pool's size.

Surface
Calcium hardness

Test your tap water. Only used when lowering.

Your result

—

Pool volume
—
Current reading
—
Guideline
—
Or, with the other strength
—
First addition (75%)
—
Rule of thumb
—

Pre-dissolve calcium chloride in a bucket of pool water — it releases heat — and add it slowly in front of a return jet. Retest after a few hours of circulation.

What calcium hardness means

Calcium hardness (CH) is the amount of dissolved calcium in the water, reported in ppm as calcium carbonate. It matters because water tries to reach a balance with the calcium in its surroundings. Water low in calcium pulls it out of plaster, grout and pebble finishes, leaving them rough and pitted. Water high in calcium, especially at high pH and temperature, drops it out as white scale on tile lines, in heaters and in salt cells. This calcium hardness calculator gives you the dose to raise it, or the share of water to replace to lower it.

How the calcium hardness calculation works

Calcium chloride is the standard way to raise hardness. Each mole of calcium chloride adds one mole of calcium, and the calculator converts the ppm you need (as calcium carbonate) to pounds of product, then divides by the product's strength.

Calcium chloride (lb) = ppm increase × gallons × 8.345 ÷ 1,000,000 × 110.98 ÷ 100.09 ÷ product purity

Calcium chloride is sold in two common strengths. Anhydrous pellets are about 94–97% calcium chloride; flake is the dihydrate form at about 77–80%. The flake needs about 23% more by weight for the same result. The calculator uses 95% and 77% for the two products.

94–97% calcium chloride needed to raise calcium hardness
Pool size+50 ppm+100 ppm+150 ppm
10,000 gal4.9 lb9.7 lb14.6 lb
15,000 gal7.3 lb14.6 lb21.9 lb
20,000 gal9.7 lb19.5 lb29.2 lb
25,000 gal12.2 lb24.4 lb36.5 lb

Worked example: a 15,000 gallon plaster pool at 200 ppm with a target of 300 ppm needs about 14.6 lb of 94–97% calcium chloride, or about 18 lb of 77% flake. Start with the 75% first addition, about 11 lb, then retest.

How to add calcium chloride

  1. Fill a clean plastic bucket about three-quarters with pool water.
  2. Add the calcium chloride to the water slowly while stirring — never water onto the product. It gets hot, so do it a few pounds at a time.
  3. With the pump running, pour the solution slowly around the deep end in front of a return jet.
  4. Brush any undissolved granules, circulate for a few hours and retest.

Safety: calcium chloride releases a lot of heat as it dissolves and can spatter. Wear eye protection and gloves, add the product to water, and do not mix it with any other chemical in the same bucket.

Lowering calcium hardness

No product a homeowner can buy removes calcium from pool water. Sequestrants can keep it from forming scale for a while, but the only way to lower the reading is to replace some water with softer water. The share to replace is:

Share to replace = (current − target) ÷ (current − fill-water hardness)

Fill-water hardness changes the answer a lot. Lowering 600 ppm to 350 ppm takes about 42% of the water if your fill water has almost no hardness, about 56% with 150 ppm tap water and about 71% with 250 ppm tap water. If your fill water is as hard as your target, draining cannot get you there; some pool services offer mobile reverse-osmosis filtering instead.

Draining has its own risks. Vinyl liners can shrink or shift, fiberglass and in-ground shells can lift when groundwater is high, and plaster can crack if left dry in the sun. Drain in stages if needed and ask a local pool professional before taking a pool down far. Use the pool fill time calculator to plan the refill.

Choosing a target

A widely used guideline is 250 to 350 ppm for plaster, pebble and other cement-based finishes, and 150 to 300 ppm for vinyl and fiberglass, which contain no calcium to protect. Those ranges are a starting point, not a rule. Hardness works together with pH, alkalinity and temperature, and the LSI calculator combines them into one number. A hot, high-pH pool may need less calcium; a cool pool with low alkalinity may need more. Heated spas often run 150 to 250 ppm for the same reason.

Common mistakes

  • Buying "calcium increaser" without checking its strength. Flake and anhydrous differ by about a quarter.
  • Dumping dry calcium chloride onto a plaster floor, where it can stain or etch the spot it lands on.
  • Using cal-hypo as your daily chlorine without testing hardness; each 1 ppm of chlorine from cal-hypo adds roughly 0.7 ppm of calcium hardness.
  • Ignoring fill-water hardness when planning a drain.

To see calcium alongside every other reading in the right order, use the pool chemical calculator.

Questions people ask

How much calcium chloride do I need to raise calcium hardness?

About 0.97 lb of 94–97% calcium chloride raises 10,000 gallons by 10 ppm. Taking a 15,000 gallon pool from 200 to 300 ppm needs about 14.6 lb, or about 18 lb of 77% flake.

What should calcium hardness be in a pool?

A common guideline is 250 to 350 ppm for plaster, pebble and other cement-based finishes and 150 to 300 ppm for vinyl and fiberglass. The right level also depends on pH, alkalinity and temperature, which the LSI combines.

How do I lower calcium hardness in my pool?

Calcium does not leave the water except by draining, so replace part of the water with softer fill water. Going from 600 to 350 ppm with 150 ppm tap water means replacing about 56% of the pool.

Is calcium increaser the same as calcium chloride?

Most pool calcium increasers are calcium chloride, either 94–97% anhydrous or about 77% flake (dihydrate). Check the label, because the two strengths need different amounts.

What happens if calcium hardness is too low?

Water low in calcium tends to be corrosive, especially when pH and alkalinity are also low. On plaster it can dissolve calcium from the surface, leaving it rough and etched.

Sources and references