Pool Alkalinity Calculator
Enter your pool volume and alkalinity reading to see how much baking soda to add — or, if TA is high, how much acid it takes and how many acid-and-aeration rounds to plan for.
Last reviewed · How we calculate
Your result
—
- Pool volume
- —
- Change
- —
- First addition (75%)
- —
- Rule of thumb for this pool
- —
- Each round
- —
- Rounds to plan for
- —
What total alkalinity does
Total alkalinity (TA) measures how much acid the water can absorb before its pH falls, reported in ppm as calcium carbonate. In a pool it is mostly bicarbonate, with a smaller share from cyanuric acid. Too little and pH swings with every rainstorm or acid dose; too much and pH creeps upward day after day as carbon dioxide escapes, which means more acid and more risk of scale. This total alkalinity calculator handles both directions: baking soda to raise it, acid and aeration to lower it.
How to raise alkalinity in a pool
Baking soda is sodium bicarbonate, the same compound most "alkalinity increaser" products contain — check the label. Each pound adds a fixed amount of alkalinity, so the dose depends only on the change you need and the water volume.
Baking soda (lb) = ppm increase × gallons × 8.345 ÷ 1,000,000 × 84.0 ÷ 50.04
The 84.0 ÷ 50.04 factor converts from "ppm as calcium carbonate" to the weight of sodium bicarbonate. The result is about 1.4 lb per 10,000 gallons for each 10 ppm.
| Pool size | +10 ppm | +20 ppm | +30 ppm |
|---|---|---|---|
| 5,000 gal | 0.70 lb | 1.40 lb | 2.10 lb |
| 10,000 gal | 1.40 lb | 2.80 lb | 4.20 lb |
| 15,000 gal | 2.10 lb | 4.20 lb | 6.30 lb |
| 20,000 gal | 2.80 lb | 5.60 lb | 8.41 lb |
| 25,000 gal | 3.50 lb | 7.00 lb | 10.51 lb |
Worked example: a 15,000 gallon pool at 60 ppm with a target of 80 ppm needs about 4.2 lb of baking soda. The calculator suggests adding about 3.15 lb first, waiting a few hours with the pump on, and retesting.
- With the pump running, broadcast the baking soda over the deep end, away from the skimmer.
- Brush any that settles on the floor so it dissolves.
- Wait a few hours (many owners wait overnight) and retest TA and pH.
- Add the rest if TA is still short. Large additions can cloud the water briefly; it clears as it dissolves.
How to lower alkalinity: acid plus aeration
Acid is the only common product that removes alkalinity. The trouble is that adding enough acid to drop TA by 50 ppm at once would crash pH, which etches plaster and corrodes metal. The usual method splits the job into rounds:
- Add enough acid to bring pH down to about 7.2. That acid converts bicarbonate into dissolved carbon dioxide and lowers TA.
- Aerate hard — fountains, waterfalls, return jets pointed at the surface, a spa spillover or an air pump. The carbon dioxide escapes and pH rises again, but alkalinity does not come back.
- When pH is back near 7.6, repeat. Stop when TA reaches your target.
The total acid needed follows directly from the alkalinity you remove: each ppm of TA takes the same amount of acid regardless of pH. That works out to about 25.6 fl oz of 31.45% muriatic acid per 10 ppm in 10,000 gallons. To estimate the number of rounds, the calculator assumes each round moves pH from 7.6 to 7.2 and uses its pH model (with your CYA) to see how much TA that removes.
Worked example: 15,000 gallons, TA 130 down to 80, CYA 40. Total acid is about 1.5 gallons (192 fl oz) of 31.45% muriatic acid. Each round of about 40.5 fl oz lowers TA about 10.6 ppm, so plan on about six rounds. With good aeration that is often one round a day.
Safety: add acid to water, never water to acid, and wear eye protection and gloves. Never mix acid with chlorine or pour them in the same place. Keep pH above about 7.0 during the process.
Picking a target
There is no single correct TA. A widely used guideline is 70 to 90 ppm for chlorine pools and 60 to 80 ppm for salt pools and pools that use trichlor tablets, because salt cells and aeration push pH up and lower TA slows that down. Plaster pools sometimes run up to about 120 ppm to help keep the water from being corrosive. If your pH rises fast, lower TA; if pH drops every time it rains or you add acid, raise it. Check the result against calcium and temperature with the LSI calculator.
Common mistakes
- Using soda ash to raise alkalinity. It does raise TA, but it raises pH a lot more; use baking soda for TA and soda ash for pH.
- Lowering TA with one big acid dose. Without aeration in between, pH falls far too low.
- Forgetting that TA and pH work together. After any TA change, use the pool pH calculator to correct pH.
- Treating every reading in isolation. The pool chemical calculator puts alkalinity first in an ordered plan.
Questions people ask
How do I raise alkalinity in my pool?
Add baking soda (sodium bicarbonate) with the pump running. About 1.4 lb raises 10,000 gallons by 10 ppm, so a 15,000 gallon pool going from 60 to 80 ppm needs about 4.2 lb.
Does baking soda raise pH?
Only a little. Baking soda has a pH of about 8.3, so it nudges pool pH up slightly but mostly raises alkalinity. Soda ash raises pH much more for the same alkalinity gain.
How do I lower total alkalinity in a pool?
Add acid to bring pH down to about 7.2, aerate the water until pH rises back toward 7.6, and repeat. Acid removes alkalinity; aeration raises pH back up without adding alkalinity, so each round lowers TA by roughly 10 ppm.
How much muriatic acid lowers alkalinity by 10 ppm?
About 25.6 fl oz of 31.45% muriatic acid lowers total alkalinity by 10 ppm in 10,000 gallons. Add it in stages so pH does not drop below about 7.0.
What should total alkalinity be in a pool?
A widely used range is 70 to 90 ppm for most chlorine pools, 60 to 80 ppm for salt pools and pools using trichlor tablets, and up to about 120 ppm for some plaster pools. The lower end keeps pH from drifting up.