Pool Dose Lab

Hot Tub Volume Calculator

Measure the inside of your hot tub, pick its shape and enter how much space the seats take up. You get gallons, liters and the weight of the water.

Last reviewed · How we calculate

Shape
Inside measurements

Footwell floor to the water line.

About 50% for acrylic spas with molded seats, 0% for an inflatable with no seats.

Your result

—

Empty-box volume
—
Taken up by seats
—
Water weight
—

Saved for the other hot tub calculators on this site. If your owner's manual lists a capacity, use that number instead.

How the hot tub volume calculator works

A hot tub volume calculator has an awkward job: the outside of a spa is a simple box, but the inside is full of molded seats, a lounger, steps and a footwell. The approach here is to work out the volume of the open space as if it were an empty shape, then subtract the share taken up by seating. You choose that share, because it varies a lot between models.

Square or rectangle: length × width × depth
Round: 3.1416 × (diameter ÷ 2)² × depth
Regular octagon: 0.8284 × (flat-to-flat width)² × depth
Gallons = cubic feet × 7.48 · Water volume = empty box × (1 − seats %)

Measurements are taken inside the shell at the water line, with depth measured from the footwell floor up to where the water sits. The octagon formula uses the width across two opposite flat sides, which is easier to measure than the corner-to-corner width.

Why seats take up so much space

It is easy to underestimate how much of a spa is shell. Jacuzzi lists its J-335, a 7 by 7 ft (84 by 84 inch) spa, at about 350 gallons; a simple box of that outside footprint and 3 ft deep would hold about 1,100 gallons. Even after allowing for the thickness of the walls and cabinet, seats, the lounger and the steps fill roughly half of the interior. That is why the calculator starts at 50% for a molded acrylic spa.

As rough starting points: around 50% for a typical acrylic spa with a lounger and sculpted seats, somewhat less for a spa with plain bench seating, roughly 10 to 20% for a round wooden tub with a narrow bench, and 0% for an inflatable tub without seats. If you know the true capacity of a similar model, you can work backwards to the right percentage for yours.

Worked example

A square acrylic spa measures 77 by 77 inches inside at the water line, and the water is 32 inches deep at the footwell. The empty box is 6.42 × 6.42 × 2.67 ft ≈ 110 cubic feet, or about 821 gallons. With 50% for seats, the tub holds about 411 gallons (about 1,550 liters), and that water weighs about 3,400 lb.

Example hot tub volumes
Tub (inside, water depth)Empty boxSeatsEstimated water
Square 70 × 70 in, 30 in deep636 gal50%318 gal
Square 77 × 77 in, 32 in deep821 gal50%411 gal
Square 90 × 90 in, 34 in deep1,192 gal50%596 gal
Octagon 84 in flat to flat, 34 in deep860 gal50%430 gal
Round wooden tub 60 in, 40 in deep490 gal15%416 gal

How to measure your hot tub

  1. Check the owner's manual or the maker's spec sheet first. A listed capacity beats any estimate.
  2. Measure the inside length and width at the water line, from shell wall to shell wall, not the outside cabinet.
  3. Measure the water depth in the footwell, from the floor to the surface. For a round or octagon tub, measure across the middle.
  4. Set the seat percentage to match your tub's interior, then compare the result with similar models.

The most accurate method is to measure while filling. Time how long your hose takes to fill a 5 gallon bucket, then time the full fill: gallons ≈ fill minutes × gallons per minute. The fill time calculator does the same math for pools.

Why volume matters

Every dose scales with volume, and hot tubs are small enough that errors show quickly. If you think your tub holds 500 gallons but it really holds 350, every dose is over 40% too strong: chlorine reads high, pH overshoots and the water can irritate skin. The result above is saved in your browser and filled in on the hot tub chemical calculator, the drain and refill calculator and the electricity cost calculator.

Weight matters too. Water weighs about 8.34 lb per US gallon, so a 400 gallon spa carries about 3,340 lb of water before the shell, the cabinet and the people in it. If the tub will sit on a deck, check the load with the deck builder or a structural engineer.

Questions people ask

How many gallons does a hot tub hold?

Most home hot tubs hold roughly 200 to 600 US gallons. Small two- to three-person and inflatable tubs are often 200 to 300 gallons, typical 7 by 7 ft acrylic spas around 350 to 450 gallons, and large 8 ft models 450 gallons or more.

How do I calculate hot tub gallons?

Multiply inside length × width × water depth in feet, then by 7.48 to get gallons. For a molded acrylic spa, subtract roughly half of that for seats, lounger and footwell steps; the manufacturer's listed capacity is more accurate if you have it.

How many gallons is a 7x7 hot tub?

Usually about 350 to 450 gallons. For example, an inside measurement of 77 by 77 inches with 32 inches of water is about 821 gallons as an empty box, or about 411 gallons after a 50% allowance for seats.

How much does a full hot tub weigh?

Water weighs about 8.34 lb per US gallon, so 400 gallons is about 3,340 lb of water alone. Add the dry weight of the spa and roughly 150 to 200 lb per person to plan a deck or slab.

Why do I need to know my hot tub volume?

Every chemical dose scales with volume. In a 400 gallon tub, 1 ppm of chlorine is only about 2.7 g of dichlor, so a 100 gallon error changes the dose by a quarter.

Sources and references