Pool Dose Lab

Pool Chlorine Calculator

Enter your pool size, free chlorine and stabilizer (CYA) readings to see exactly how much of your chlorine product to add, plus the CYA or calcium it brings with it.

Last reviewed · How we calculate

Your pool

Not sure? Work it out from your pool's size.

Test results

FC, not total chlorine. Use 0 if the test shows none.

Stabilizer. Use 0 for an unstabilized indoor pool.

Dose

Filled in from your CYA. Type your own to override.

Check the percentage on your label.

Your result

—

Pool volume
—
Raise free chlorine by
—
FC range for your CYA
—
Shock (SLAM) level
—

    Add with the pump running, wait 30 minutes, then retest. Free chlorine drops every day from sunlight and swimmers, so this is a single top-up, not a weekly total.

    How much chlorine to add to a pool

    Working out how much chlorine to add to a pool takes three numbers: how many gallons you have, how far your free chlorine (FC) is below where it should be, and how strong your product is. This pool chlorine calculator also sets the target for you from your cyanuric acid (CYA) reading, because the right FC level depends on how much stabilizer is in the water.

    One part per million is one milligram per liter. To raise a pool by a given number of ppm, you need that many milligrams of available chlorine for every liter of water. Divide by the strength of your product and you have the dose.

    Available chlorine (g) = ppm increase × gallons × 3.785 ÷ 1,000
    Liquid (L) = grams ÷ grams per liter in the jug · Solid (g) = grams ÷ % available chlorine

    The tool assumes 125 g/L for 12.5% liquid chlorine and 100 g/L for 10%. Household bleach is labelled as percent sodium hypochlorite by weight, which is about 95% of the same figure as available chlorine, so 6% bleach carries about 62 g/L and 8.25% about 88 g/L. Solids are labelled by available chlorine: 73% cal-hypo means 0.73 lb of chlorine per pound of product.

    Worked example: 15,000 gallons, FC 1, CYA 40

    With 40 ppm stabilizer, the common CYA-ratio guideline gives a minimum of 3 ppm and a target of about 4.6 ppm, so the pool needs 3.6 ppm more. That is 3.6 × 15,000 × 3.785 ÷ 1,000 ≈ 204 g of available chlorine. In 10% liquid chlorine that is about 2.04 L, or 69 fl oz — a little over half a gallon. The same job takes about 55 fl oz of 12.5% liquid, about 9.9 oz of 73% cal-hypo or about 12.9 oz of dichlor. The dichlor would also add about 3.2 ppm of CYA, and the cal-hypo about 2.9 ppm of calcium hardness.

    Chlorine product comparison

    Amount to raise free chlorine in 10,000 US gallons
    Product+1 ppm+5 ppmSide effect at +5 ppm
    Liquid chlorine 12.5%10.2 fl oz51 fl oz (0.40 gal)None (raises pH briefly)
    Liquid chlorine 10%12.8 fl oz64 fl oz (0.50 gal)None (raises pH briefly)
    Bleach 8.25%14.5 fl oz73 fl oz (0.57 gal)None
    Bleach 6%20.7 fl oz104 fl oz (0.81 gal)None
    Cal-hypo 73%1.8 oz9.1 oz+3.5 ppm calcium hardness
    Cal-hypo 65%2.1 oz10.3 oz+3.5 ppm calcium hardness
    Dichlor 56%2.4 oz11.9 oz+4.5 ppm CYA
    Trichlor 90%1.5 oz7.4 oz+3 ppm CYA, lowers pH and alkalinity
    Lithium hypochlorite 35%3.8 oz19.1 ozNone significant

    Solid amounts are by weight, not by volume. For any other pool size, scale in proportion: 20,000 gallons needs twice the table amount.

    Why CYA sets your chlorine target

    Cyanuric acid shields chlorine from sunlight, but it also holds most of the free chlorine in a weakly active, bound form. Only the small unbound share — hypochlorous acid — does most of the sanitizing, and that share depends on the ratio of FC to CYA. A widely used guideline, popularized by the Trouble Free Pool method, keeps FC at no less than about 7.5% of CYA, aims for about 11.5%, and treats algae at about 40%. Salt pools can run lower (about 5% minimum and 7.5% target) because the generator adds chlorine continuously. These are practical guidelines rather than legal limits; for public pools, health codes based on the CDC Model Aquatic Health Code set the minimums. The full table is on the chlorine CYA chart.

    How to add chlorine safely

    1. Test FC and CYA with a reliable kit. A FAS-DPD drop test reads FC far more precisely than strips.
    2. Run the pump. Pour liquid chlorine slowly in front of a return jet, close to the water surface to avoid splashing.
    3. Pre-dissolve cal-hypo in a bucket of pool water, adding the granules to the water, and pour the liquid in. Undissolved granules can bleach vinyl liners.
    4. Put trichlor only in a floater or feeder, never loose in the skimmer with other chemicals.
    5. Brush, wait 30 minutes, and retest before adding more.

    Always add chemicals to water, never water to chemicals. Never mix two chlorine products, and never mix chlorine with acid — cal-hypo and trichlor together can react violently, and chlorine plus acid releases chlorine gas. Wear eye protection and follow the label.

    Choosing a product

    Liquid chlorine and plain bleach add nothing but chlorine and a little salt, which makes them the easiest products to dose day to day. Stabilized products (dichlor and trichlor) are convenient but keep adding CYA: every 10 ppm of FC from dichlor adds about 9 ppm of CYA, and from trichlor about 6 ppm. Over a season that can push stabilizer high enough that your FC target climbs out of reach, and the only fix is draining. Cal-hypo adds calcium instead, which matters if your water is already hard. Lithium hypochlorite adds neither, but is much weaker per pound.

    Common mistakes

    • Dosing from total chlorine instead of free chlorine. If total is well above free, you have combined chlorine — see the pool shock calculator.
    • Using an old jug. Liquid chlorine loses strength in storage, especially in heat, so a jug from last summer may be well below its label.
    • Ignoring CYA. If your stabilizer is above about 80 ppm, check the cyanuric acid calculator to see how much water to replace.
    • Forgetting pH. Chlorine works best with pH around 7.4 to 7.6; the pool chemical calculator puts all your readings in order.

    Questions people ask

    How much liquid chlorine do I add to raise free chlorine by 1 ppm?

    In 10,000 gallons, about 10.2 fl oz of 12.5% liquid chlorine or 12.8 fl oz of 10% liquid chlorine raises free chlorine by 1 ppm. Double the pool size and you double the amount.

    How much chlorine should I add to a 15,000 gallon pool?

    It depends on the gap between your reading and your target. Raising a 15,000 gallon pool from 1 to 4.6 ppm (the target for 40 ppm CYA) takes about 69 fl oz (just over half a gallon) of 10% liquid chlorine or about 10 oz of 73% cal-hypo.

    What free chlorine level should my pool have?

    A widely used guideline ties free chlorine to stabilizer: a minimum of about 7.5% of the CYA level and a target of about 11.5%. With 40 ppm CYA that means at least 3 ppm and ideally around 4.6 ppm. Indoor pools without CYA can run at 1 to 3 ppm.

    Is household bleach the same as pool chlorine?

    Plain unscented bleach is the same chemical (sodium hypochlorite), just weaker: 6% or 8.25% instead of 10 to 12.5%. Use only regular bleach without scents, thickeners or splash-less additives, and add proportionally more of it.

    Why does my pool need more chlorine than the bottle says?

    Most labels assume low stabilizer. Cyanuric acid binds most of the free chlorine, so the more CYA you have, the higher the free chlorine reading must be for the same sanitizing power. At 80 ppm CYA the target is about 9.2 ppm, not 3.

    Sources and references