Pool Dose Lab

Chlorine CYA Chart

Enter your CYA (stabilizer) reading and, if you like, your free chlorine reading. You get the minimum, target and shock chlorine levels and whether your reading is in range.

Last reviewed · How we calculate

Your readings

Stabilizer. Use 0 for an unstabilized indoor pool.

Optional. Leave blank to see the levels only.

Your result

—

Minimum FC
—
Target FC
—
Shock (SLAM) FC
—
Your FC
—
Other pool type
—

    These are widely used guidelines, not legal limits. Public pools must follow their state or local health code.

    How to read a chlorine CYA chart

    A chlorine CYA chart tells you how much free chlorine (FC) your pool needs for the amount of cyanuric acid (CYA, stabilizer or conditioner) in the water. The tool above and the chart below use the CYA-ratio approach popularized by the Trouble Free Pool (TFP) method: the more stabilizer you have, the higher the free chlorine reading must be to do the same job.

    Chlorine pools: minimum ≈ 7.5% of CYA · target ≈ 11.5% of CYA · shock ≈ 40% of CYA (never below 10 ppm)
    Salt pools: minimum ≈ 5% of CYA · target ≈ 7.5% of CYA · shock ≈ 40% of CYA (never below 10 ppm)

    Minimums are never set below 1 ppm and targets never below 2 ppm. With no CYA at all (an indoor pool), the common guideline is 1 to 3 ppm FC with 10 ppm for shocking.

    Free chlorine by CYA level

    Free chlorine (ppm) by cyanuric acid level
    CYA (ppm)Chlorine pool minimumChlorine pool targetSalt pool minimumSalt pool targetShock / SLAM
    0131310
    10121210
    201.52.31210
    302.33.51.52.312
    4034.62316
    503.85.82.53.820
    604.56.934.524
    705.38.13.55.328
    8069.24632
    906.810.44.56.836
    1007.511.557.540

    The 0 row is the separate guideline for unstabilized water. From 10 ppm up, minimum and target follow the ratios; the shock level is held at 10 ppm until 40% of CYA passes that, so low-stabilizer pools are never shocked more weakly than unstabilized ones. TFP's own published chart rounds to whole numbers and gives target ranges (for example 4 to 6 ppm at 30 ppm CYA), so you will see small differences. Treat the target as a sensible middle, not a hard line: anything between the minimum and a few ppm above the target is fine for daily running.

    Why stabilizer changes the chlorine you need

    When chlorine dissolves in water it forms hypochlorous acid (HOCl), the fast-acting sanitizer, and hypochlorite ion, which is much weaker. Sunlight destroys both quickly. Cyanuric acid protects chlorine by holding most of it in a loosely bound form that UV light does not break down as fast. The bound chlorine is released as the free HOCl gets used up, so the pool keeps a reserve through the day.

    The trade-off is that the share of chlorine left as active HOCl depends mostly on the ratio of FC to CYA. Keep the ratio the same and the sanitizing strength stays about the same; let CYA climb while FC stays fixed and the water gets weaker. That is why 3 ppm FC is plenty at 20 ppm CYA but not enough at 80 ppm, and why the "1 to 3 ppm" range printed on many test kits only applies to water with little or no stabilizer.

    pH matters too. HOCl is a weak acid, and as pH rises more of it turns into hypochlorite, so chlorine is somewhat more effective around pH 7.4 than at 7.8 or higher.

    Worked example

    A salt pool tests 70 ppm CYA and 3 ppm FC. With the generator, the minimum is 3.5 ppm and the target 5.3 ppm, so the pool is slightly under the minimum: raise the generator output or add some liquid chlorine to get above 3.5 ppm, then aim for about 5. If the same pool were chlorinated by hand, the minimum at 70 ppm CYA would be 5.3 ppm and the target 8.1 ppm. Use the pool chlorine calculator to turn that gap into ounces or gallons of product.

    How to use the chart day to day

    1. Test CYA every few weeks; it changes slowly. Test FC daily in hot weather until you know how fast your pool uses chlorine.
    2. Add chlorine so FC does not fall below the minimum before your next dose. In practice that means dosing up to or a little above the target.
    3. If FC ever reads below the minimum, or the water turns cloudy or green, raise it to the shock level and hold it there. The pool shock calculator works out the amount.
    4. If CYA is above about 80 ppm in a chlorine pool, the levels become hard to keep up with. Replacing part of the water is the only practical way down; see the cyanuric acid calculator.

    Common guidelines for stabilizer are 30 to 50 ppm CYA for pools chlorinated with liquid chlorine or tablets, and 60 to 80 ppm for salt water pools. Tablets (trichlor) and dichlor add CYA every time you use them.

    Guideline, not law

    The FC/CYA ratios are a practical rule of thumb widely used by residential pool owners. They are not a legal standard. For public and commercial pools, state and local health codes set the rules, many of them based on the CDC's Model Aquatic Health Code. The CDC recommends at least 1 ppm free chlorine in pools and 3 ppm in hot tubs, and some codes also cap CYA. Those minimums are floors for regulated pools; with stabilized water, the ratio method usually asks for more.

    When raising chlorine, add products to water, never water to products. Never mix two different chlorine products or chlorine with acid, wear eye protection and follow the label.

    Questions people ask

    What should free chlorine be with 50 ppm CYA?

    Using the common CYA-ratio guideline, a chlorine pool at 50 ppm CYA should stay at or above about 3.8 ppm FC, with a target near 5.8 ppm and a shock level of 20 ppm. A salt pool at the same CYA can run a little lower, with a target near 3.8 ppm.

    Why does higher CYA need more chlorine?

    Cyanuric acid binds most of the free chlorine into a weaker, protected form. The active part, hypochlorous acid, depends on the ratio of free chlorine to CYA, so doubling CYA roughly doubles the FC you need for the same effect.

    What is the ideal CYA level for a pool?

    A common guideline is 30 to 50 ppm for pools chlorinated by hand and 60 to 80 ppm for salt water pools. Indoor pools that get no direct sun often run without CYA.

    Is 3 ppm chlorine enough?

    With 0 to about 30 ppm CYA, yes. With 40 ppm CYA, 3 ppm is the minimum. With 80 ppm CYA, 3 ppm is only half of the 6 ppm minimum, and algae can start to grow.

    Why is the salt pool target lower?

    A salt chlorine generator makes chlorine continuously in small amounts, so FC does not swing as low between doses. Salt pools are commonly run at about 5% to 7.5% of CYA instead of 7.5% to 11.5%.

    Sources and references