How we calculate
Every number on this site comes from a formula you can check. This page lists them in one place, along with the product strengths and target ranges we assume.
Parts per million and pool volume
Pool test kits report levels in parts per million (ppm), which in water is the same as milligrams per liter. One US gallon is 3.785 liters and weighs about 8.345 lb, so raising one gallon by 1 ppm takes 8.345 millionths of a pound of the active chemical. Almost every dose on this site starts from that conversion:
active chemical (lb) = ppm change × gallons × 8.345 ÷ 1,000,000 active chemical (g) = ppm change × gallons × 3.785 ÷ 1,000
Volume formulas use 7.48 US gallons per cubic foot and 264.17 gallons per cubic meter. Rectangles use the average of the shallow and deep depths, round and oval pools use the area of a circle or ellipse, and kidney pools use the industry approximation 0.45 × (width A + width B) × length × depth.
Chlorine products
A chlorine product's strength is the share of "available chlorine" it delivers. We divide the chlorine needed by that strength:
| Product | Strength used | Side effect per 1 ppm chlorine |
|---|---|---|
| Liquid chlorine 12.5% / 10% | 125 / 100 g available chlorine per liter | none (raises pH slightly at first) |
| Bleach 8.25% / 6% | about 88 / 62 g per liter (label % × 0.95 × density) | none |
| Cal-hypo 73% / 65% | 73% / 65% by weight | about +0.7 ppm calcium hardness |
| Dichlor 56% | 56% by weight | about +0.9 ppm stabilizer (CYA) |
| Trichlor 90% | 90% by weight | about +0.6 ppm stabilizer (CYA) |
Strengths vary by brand and fall as products age — liquid chlorine loses strength in heat and sunlight within weeks. If your label lists a different percentage, choose the closest product or adjust the result proportionally.
Chlorine targets and stabilizer
Stabilizer (cyanuric acid, CYA) protects chlorine from sunlight but also holds much of it in reserve, so the chlorine level a pool needs rises with CYA. We use a widely used guideline: a minimum free chlorine of about 7.5% of the CYA level, a target near 11.5%, and about 40% for clearing algae. Salt pools, which make chlorine continuously, use about 5% minimum and 7.5% target. Pools without stabilizer use 1–3 ppm. Public pools must also meet their local health code, which can set different minimums.
pH, alkalinity and acid
Acid and soda ash amounts come from a carbonate-equilibrium model, not a fixed "ounces per 0.1 pH" rule. From your total alkalinity, pH and stabilizer level we estimate the dissolved carbonate in the water (subtracting the part of the alkalinity reading that comes from cyanurate), then work out how many acid or base equivalents move the pH to your target. We use acid constants of pK₁ = 6.3 and pK₂ = 10.25 for carbonate and 6.88 for cyanuric acid, typical for pool water near 77–85 °F. Muriatic acid 31.45% is treated as about 10 equivalents per liter, 14.5% as about 4.3, and dry acid as 93% sodium bisulfate.
Lowering total alkalinity by 10 ppm in 10,000 gallons takes about 25.6 fl oz of 31.45% muriatic acid, and raising it by 10 ppm takes about 1.4 lb of baking soda. Both figures fall straight out of the equivalent weights and match long-published pool industry rules of thumb.
Real water also contains borates, phosphates and dissolved carbon dioxide that change with temperature and splashing. That is why every pH result tells you to add about three-quarters, circulate, and retest.
Water balance (LSI)
The Langelier Saturation Index is calculated as pH + temperature factor + calcium factor + alkalinity factor − TDS factor, using the standard pool-industry factor table. The alkalinity factor uses carbonate alkalinity (total alkalinity minus about one-third of the CYA level at normal pH). An LSI between −0.3 and +0.3 is generally considered balanced.
Typical ranges we show
- pH 7.4–7.6 (7.2–7.8 acceptable)
- Total alkalinity 70–90 ppm for most pools, 60–80 ppm for salt and trichlor-fed pools, up to about 120 ppm for some plaster pools
- Stabilizer 30–50 ppm (chlorine pools), 60–80 ppm (salt pools)
- Calcium hardness 250–350 ppm for plaster or pebble finishes, 150–300 ppm for vinyl and fiberglass
- Salt: the range in your generator's manual, commonly 2,700–3,400 ppm
- Hot tubs: 3–5 ppm chlorine or bromine, pH 7.4–7.6, alkalinity 50–80 ppm
Energy and equipment
Heating estimates use 8.345 BTU to raise one gallon of water by 1 °F, 3,412 BTU per kWh and 100,000 BTU per therm. Variable-speed pump savings use the pump affinity law, where power changes roughly with the cube of speed. These are physics-based estimates; real equipment efficiency, wind, shade and plumbing change the result.
Limits and corrections
The calculators are written for residential pools and hot tubs. They do not replace a product label, a professional water test, or your local health code. If you find a number that looks wrong, tell us — we recheck the formula, correct the page and update its review date.