Pool Dose Lab

Pool pH Calculator

Enter your pool volume, pH, alkalinity and stabilizer to see how much acid lowers pH — or how much soda ash raises it — and what your alkalinity will be afterward.

Last reviewed · How we calculate

Your pool

Not sure? Work it out from your pool's size.

Readings

7.4–7.6 is a common target.

0 for an unstabilized indoor pool.

Leave at 0 unless you add borates.

Your result

—

Pool volume
—
pH change
—
First addition (75%)
—
Same change with
—
Estimated new alkalinity
—
Carbonate alkalinity
—

Results are estimates from a carbonate-equilibrium model with a CYA correction. Test kits read pH to about ±0.1, so add about 75%, circulate for an hour and retest.

How this pool pH calculator works

Most pH charts give one acid dose per 10,000 gallons and ignore everything else in the water. That is why the same chart can be right for one pool and badly off for the next. This pool pH calculator works out the dose from the water's buffering. Total alkalinity is mostly bicarbonate, which soaks up acid; cyanuric acid (stabilizer) and borates add buffering of their own. The higher those are, the more acid or soda ash it takes to move pH by the same amount.

The model first removes the part of your alkalinity reading that comes from CYA (and borates, if entered), which leaves the carbonate alkalinity. From that it estimates the total dissolved carbonate in the water. To lower pH, it calculates how much alkalinity disappears when that same carbonate is moved to the target pH; every equivalent of alkalinity lost takes one equivalent of acid. To raise pH, it solves for the soda ash that adds just enough carbonate and alkalinity to land on the target.

Acid needed = [total alkalinity at current pH − total alkalinity at target pH] × water volume, with dissolved carbonate held constant

Like every pH calculator, this is an estimate. Test-kit pH is read to about 0.1 units, and temperature, salt and fresh carbon dioxide from rain or fill water all shift the result. Add about three-quarters of the dose, circulate, and retest before adding more.

Worked example: how to lower pH in a pool

A 15,000 gallon pool reads pH 7.9, total alkalinity 90 ppm and CYA 40 ppm. The calculator gives about 17.6 fl oz (519 mL) of 31.45% muriatic acid to reach 7.5. The same change takes about 41.3 fl oz of 14.5% low-fume acid or 1.48 lb of dry acid. The 75% first addition is about 12 fl oz. Because acid consumes alkalinity, TA will read about 85 ppm afterward.

  1. Put on eye protection and gloves. Check the label strength — 31.45% and 14.5% acid need very different amounts.
  2. With the pump running, pour the acid slowly into the water in front of a return jet, low over the surface, away from the skimmer and any metal fittings.
  3. Brush the floor where it was poured and let the pool circulate for about an hour.
  4. Retest pH. Add the remaining amount only if it is still above target.

Safety: add acid to water, never water to acid. Never mix acid with chlorine or pour them in the same place, and keep acid stored apart from chlorine. Dilute in a plastic bucket of pool water only if the label tells you to.

Acid per 10,000 gallons by alkalinity and CYA

31.45% muriatic acid to lower pH from 7.8 to 7.5 in 10,000 US gallons
Total alkalinityCYA 0CYA 40CYA 80
60 ppm4.8 fl oz7.2 fl oz9.5 fl oz
80 ppm6.4 fl oz8.8 fl oz11.1 fl oz
100 ppm8.0 fl oz10.4 fl oz12.7 fl oz
120 ppm9.6 fl oz12.0 fl oz14.3 fl oz

Two patterns stand out. Doubling alkalinity roughly doubles the acid, and stabilizer adds buffering of its own, so a pool with more CYA needs more acid at the same TA reading. Borates are an even stronger buffer near pool pH: at 50 ppm borates the example pool above needs about 44 fl oz instead of 17.6.

Raising pH: soda ash or aeration

Soda ash (sodium carbonate) raises pH quickly and also raises alkalinity. For a 10,000 gallon pool at pH 7.2 with TA 80 and CYA 40, the calculator gives about 1.04 lb (16.6 oz) of soda ash to reach 7.5, and TA rises to about 92 ppm. Dissolve it in a bucket of pool water first; poured dry, it can cloud the water for a while.

Aeration raises pH without adding any alkalinity. Water holds dissolved carbon dioxide, and when you splash it — waterfalls, fountains, return jets aimed up, an air blower — that carbon dioxide escapes and pH climbs. It is slower than soda ash but costs nothing, and it is the better choice when TA is already at or above the range you want. If alkalinity is low as well as pH, raise alkalinity with baking soda first using the pool alkalinity calculator; that often brings pH up enough on its own.

Common mistakes

  • Ignoring alkalinity. A pool at TA 150 needs about two to two and a half times the acid of one at TA 60 for the same pH change, depending on CYA.
  • Chasing pH every day. If pH keeps rising, the fix is usually lower alkalinity, not more acid more often.
  • Testing right after adding chlorine. Very high chlorine bleaches the pH indicator dye and gives false readings; Taylor-style kits use a thiosulfate drop to prevent this.
  • Adding acid and chlorine back to back in the same spot.

pH also drives scale and corrosion. Check the combined effect with the LSI calculator, or enter a full test in the pool chemical calculator to get every adjustment in order.

Questions people ask

How do I lower the pH in my pool?

Add muriatic acid or dry acid (sodium bisulfate) with the pump running, pouring slowly in front of a return jet. For a 15,000 gallon pool with TA 90 and CYA 40, going from pH 7.9 to 7.5 takes about 17.6 fl oz of 31.45% muriatic acid; add about three-quarters and retest after an hour.

How much muriatic acid do I need to lower pH by 0.3 in 10,000 gallons?

With CYA at 40 ppm, taking pH from 7.8 to 7.5 needs about 7.2 fl oz of 31.45% acid at TA 60, 8.8 fl oz at TA 80 and 10.4 fl oz at TA 100. Higher alkalinity means more acid for the same change.

Why does my pool pH keep going up?

Dissolved carbon dioxide escapes from the water, especially with high alkalinity, aeration, waterfalls, spa spillovers or salt cells, and that loss raises pH. Lowering total alkalinity toward 60 to 80 ppm usually slows the rise.

How do I raise pH without raising alkalinity?

Aerate the water: run fountains, waterfalls or point return jets at the surface. Aeration drives out carbon dioxide and raises pH while total alkalinity stays the same. Soda ash raises both.

What should pool pH be?

A common target is 7.4 to 7.6, with 7.2 to 7.8 generally acceptable. Chlorine works better toward the low end, and scale forms more easily toward the high end.

Sources and references